Dial Diameter: 37mm/1.46 inches
Strap Width: 15mm/0.59 inches
Thickness: 6mm/0.24 inches
Product Weight: About 20g
Compatibility: IOS8.0 and above & Android 4.4 and above
Because the watch is smart, please charge more than 2 hours for a single charge. Do not support high-power charger charging, it is recommended to use a laptop or computer host to charge.
Battery: USB charging
Features: Calorie, Pedometer, Distance, Remote Camera, Water Resistant, Sleep Monitor, Alarm, Call-ID, Message Reminder, Long Standby
How to connect the Bracelet?
Make sure the bracelet is powered on, the Bluetooth is turned on in the phone. Please search and download the “FlagFit” APP in the app store first, or scan the two-dimensional code on the back of the watch box to download “FlagFit”.
Open the APP software, click “Device”, pull down the phone screen, refresh the device that APP can search, find the “TLW08” Bluetooth device, click the link. When the link is successful, please synchronize the APP data (Android phones can click “Shake to take a picture” to synchronize the data, Apple phones in the sleep detection page, pull down the phone screen synchronization data), and then you can see the “phone reminder” function in the “push message” or the APP interface.
If you need them, you can open them, and use them normally. If you see the bracelet is not connected, try to restart the phone’s Bluetooth. If you restart the Bluetooth or the connection is not on the phone Bluetooth settings, click ！ into the secondary interface, ignore the device; then enter the App, click on the connected device to try again.
How long can a bracelet battery last?
After receiving the bracelet, you first need to use a matching charging tool to charge the bracelet. Single charge more than 2 hours, it is recommended that you use low-power charging equipment, such as a notebook or computer mainframe charging, do not use a high-power charger.
The principle of smartwatches is like smartphones. If you don’t use them often, bracelets can stand for 3 to 5 days. If you use it regularly and turn on all the features, the bracelet battery will normally last 24 to 72 hours. The standby time of the battery is determined according to the frequency of your use. I hope you can understand it. Of course, after the battery is used, you can charge the battery again.
1. Why do not connect on the watch?
①Please search and download the “FlagFit” APP in the app store first, or scan the two-dimensional code on the back of the watch box to download “FlagFit”.
② Please confirm that the bracelet has been switched on.
③Please confirm the bracelet in the vicinity, and there is power.
④First look at the bracelet device is connected. In the phone Bluetooth settings, you will see all the Bluetooth-enabled devices.
⑤If you see the bracelet is not connected, try to restart the phone’s Bluetooth.
⑥If you restart the Bluetooth or the connection is not on the phone Bluetooth settings, click ！ into the secondary interface, ignore the device; then enter the App, click on the connected device to try again.
2. Why does the watch have no electricity after 3 days?
Please be sure to close the heart rate and sleep state detection when the detection is completed, avoiding heart rate and sleep state detection LED long time to open, accelerating the power consumption.
3. How to monitor sleep?
When the user wearing band enters the sleep state at night, the band will automatically switch to the monitoring sleep mode. More details about sleeping can be viewed through the APP.
4. How to Synchronous Data?
①Just connecting the band, APK will automatically sync bedtime, personal information, step, sleep data, screen time, sedentary reminder, alarm clock, time system (whether 24 hours), etc.
②Syncs data by pull-down under Exercise, Sleep, and Heart Rate interfaces.
Warm reminder: Seven days offline-data is saved. The more the data is , the longer it takes to sync a maximum of nearly 2 minutes. “Sync finished” will be shown after syncing done.
5. Why can’t some phones scan the device?
Some mobile phones cannot scan devices because of the system itself, such as the Android6.0 system easily appearing this kind of problem. Current solution: Open the phone GPS first, and then re-scan the device.
6. Why does “Shake to take a picture” not use?
Please allow the app accessing to the camera before you use the camera.
You can open the last column “Help” of the “FlagFit” APP, and have more watches guide and function introduction.